NEW 10" x 54" SHARP MODEL TMV VERTICAL KNEE MILL

Manufacturer

SHARP

Model

TMV

Year

Not provided

Stock #

14552

Condition

New

Request A Quote

Keep Scrolling To Learn More

Specifications

Equipped With

NEW 10" x 54" SHARP MODEL TMV VERTICAL KNEE MILL 

These vertical knee mills are equipped with vari-speed drive, available with optional digital vari-speed. The dove tail ways chromed, and the box ways are hardened and ground.  


Head  
  • To dissipate heat in the 3 HP motor driven head, a pair of high output fans is installed. This allows the machine to work demanding jobs for extended periods without damaging the motor, belts and bearings. A unique SHARP feature.
  • The motor shaft and Vari Drive pulleys are dynamically balanced, then hard-chromed. This allows a vibration free milling even at high speed
 
  • Since the Vari-speed drive system is operated by sliding the Vari Drive pulley up and down the motor shaft. The motor shaft is therefore chrome-plated, and has an oil channel that is fed by a grease fitting on the lower end for self-lubricating purpose. This ensures the sliding motion is trouble free at all times. A unique SHARP feature.
  • The motor shaft that drives the pulley and the spindle is subject to a lot of lateral stress. A roller bearing is installed for the lower support of the motor shaft. A unique SHARP feature.
  • Beside swiveling 90 degree side to side, the head can also swivel up and down by virtue of a knuckle joint design. The new design developed by Sharp uses 6 bolts, 3 each side, that fitted into a circular T-slot milled at the inside of the over arm and secured by nuts from the outside. It secured the head tightly and offered high accuracy in milling operations.
  • A matched pair of super-precision ABEC-7 angular contact bearings supports the spindle. The quill is CNC-ground to a mirror finish, and then chromed to fit the housing. Together, they insure spindle run out of no more than 0.0004” TIR- the best in the industry.
 
Column, Table and Knee  
  • Hardened and ground box ways on column and saddle.
  • Turcite coated slideways for better resistance to wear and retention of lube oil.
 
  • Certified MEEHANITE castings are used for superior rigidity and better dampening of vibrations.
 
  • Table and saddle backlash is controlled by a double-nut design that keeps the feed screw in contact with a pair of bronze nut at all times. A unique SHARP feature.
  • Hardened leadscrews on table and saddle for better resistance to wear.
 
  • The end of the table and saddle are mounted with thrust bearings that pre-load the feed screw, eliminating endplay for precisely controlled lateral movement.
  • Instead of hand scraping the top of the knee ways for oil retention, the matching underside of the saddle is hand-scraped. This extra step avoids having chips and dirt embedded in the knee ways and damages the sliding area.

 

  • "Bridgeport-style" mill
 
Why DVS head?  
  • High reliability with fewer moving parts than regular vari speed head
  • Dynamic brake
  • Low voltage control
  • Large Digital rpm display
  • Fully enclosed display unit
  • Dependable Inverter Drive System
  • Machine can run on single phase or 3 phase electricity
  • Safety device prevents machine from self starting after power failure or after emergency stop being pushed
TABLE  
Working surface 10”x 54"
T-slot number, size 3, 5/8"
CAPACITY  
Table travel (X-axis) 35"
Saddle travel (Y-axis) 16.3"
Ram travel 18.5"
Quill travel (Z-axis) 5"
Knee travel 15.3"
Throat distance (min-max) 9.8” - 28.3"
Spindle gage line to table top 1.6”- 16.9"
SPINDLE  
Motor 3 HP
Wiring voltage 220V / 440V, 3 Ph, 60 Hz
Taper R-8
Speed (vari-speed) 60-4,500 RPM
Quill feed (IPR) 0.0015, 0.003, and 0.005
Spindle Accuracy 0.0002" TIR
Head tilt; right to left (each way) 90º
Head tilt; up-and-down (each way) 45º
DIMENSIONS AND WEIGHT  
Floor area (w x d) 70" x 75"'
Height 88"
Net weight (lbs; approximately) 3,000

STANDARD ACCESSORIES:

  • Hardened and ground box ways
  • Draw bar 
  • Front and rear way cover 
  • One-shot lube system 
  • Toolbox with tools

OPTIONAL ACCESSORIES:

  • Digital Variable Speed (DVS) Head 
  • Power feed system on table, saddle & knee 
  • Power draw bar 
  • Riser block (4" or 7") 
  • Right angle milling attachment 
  • Coolant system with chip pan 
  • Milling vise
  • Clamping kit 
  • Halogen work light 
  • R-8 Collets 

TMV
TABLE  
Working surface 10”x 50"
T-slot number, size 3, 5/8"
CAPACITY  
Table travel (X-axis) 35"
Saddle travel (Y-axis) 16.3"
Ram travel 18.5"
Quill travel (Z-axis) 5"
Knee travel 15.3"
Throat distance (min-max) 9.8” - 28.3"
Spindle gage line to table top 1.6”- 16.9"
SPINDLE  
Motor 3 HP
Wiring voltage 220V / 440V, 3 Ph, 60 Hz
Taper R-8
Speed (vari-speed) 60-4,500 RPM
Quill feed (IPR) 0.0015, 0.003, and 0.005
Spindle Accuracy 0.0002" TIR
Head tilt; right to left (each way) 90º
Head tilt; up-and-down (each way) 45º
DIMENSIONS AND WEIGHT  
Floor area (w x d) 70" x 75"'
Height 88"
Net weight (lbs; approximately) 3,000

Attachments

There are no files attached to this listing currently. If you Have any further questions regarding this listing, please contact us for more information.

Blumberg Machinery is proud to offer a slew of services from appraisals, financing, auction services, and more.

View All Services